encor 350 401

encor 350 401

• 6119 Reviews

The router illustrated in Figure 10.12 is configured as shown in the following output: Because routing protocols have different characteristics, they differ in their scalability and performance. Some routing protocols are suitable only for small networks, while others may be used in small, medium, and large networks. Rebinding (T2) timer (default: 87.5% of the lease time): This second timer is used in situations in which the DHCP server does not answer or confirm the allocation extension after the renewal timer expires. This timer states that if 7/8ths of the lease time has passed, the client will try to find (send a DHCP Request) other DHCP servers which might be able to provide a DHCP address. dot1q - Interface uses only 802.1q trunking encapsulation when trunking The same principle applies when you have a network with two host bits, as you will need to enter an ACL to match these. For example, matching subnet 192.168.1.0 255.255.255.252 or /30, you will need to enter the following: Switch#conf t Switch(config)#int fa0/0 Switch(config-if)#shutdown same view of and agree on optimal routes. When convergence takes a long time to occur, intermittent packet loss and loss of connectivity may be experienced between remote networks. In addition to these problems, slow convergence can result in network routing loops and outright network outages. Based on what you know about CDP, the LLDP output should look very familiar. Most importantly, the interface information, such as local and remote port information, is the same between both protocols and is very useful when analyzing or troubleshooting a network. You can enable LLDP globally or per interface. Switch-1(config-if-range)#switchport access vlan 10 Switch-1(config-if-range)#switchport mode access Switch-1(config-if-range)#exit Figure 10.7 shows the same packet leaving Router A for Router B. There is a route lookup and then the packet is switched out of interface E1. Type 800 indicates that the packet is IPv4. (P) Repeater, (S) Station, (O) Other that might help you determine the point in the network where problems occur. System image file is “flash:/c3560-advipservicesk9-mz.122-35.SE1.bin” MAC Spoofing Attacks BranchRouter(config)#ip route 192.168.1.0 255.255.255.0 172.16.5.3 115 Load Verify the switch mac address table Configure a password on the VTY lines C 192.168.1.0 is directly connected, Serial0/1/0 RouterA# WORD VLAN IDs of the allowed VLANs when this port is in trunking mode add add VLANs to the current list In Figure 15.5 above, the incoming packet has a source and destination address, but your standard ACL will only look at the source address. Your ACL would permit or deny this source address (see Figure 15.6): Cisco IOS Software, C2960 Software (C2960-LANBASE-M), Version 12.2(25)FX, RELEASE SOFTWARE (fc1) MAC Spoofing Attacks R1(config)#interface FastEthernet0/0.30 Switch-1(config)#interface GigabitEthernet0/2 Switch-1(config-if)#switchport port-security The route above is actually a default route. Default routes are used to direct packets addressed to networks not explicitly listed in the routing table. We cover these as well as your other options in more detail below. Topology Fa0/6, Fa0/7, Fa0/8, Fa0/9, Fa0/10, Fa0/11, Fa0/12, Fa0/13, Fa0/14, Fa0/15, Fa0/16, Fa0/17, Fa0/18, Fa0/19, Fa0/20, Fa0/21, Fa0/22, Fa0/23, Fa0/24 % LLDP is not enabled Switch#conf t Switch(config)#lldp run Enter configuration commands, one per line. End with CNTL/Z. Router(config)#no access-list 1 Router0# R2(config-router)#network 172.16.0.0 password-encryption Encrypt system passwords password-recovery Disable password recovery prompt Enable mode specific prompt RIP Passive Interfaces Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) [Truncated Output] Switchport: Enabled Administrative Mode: static access Operational Mode: static access Total entries displayed: 1 Walkthrough Verify (show) the VTP configuration on both switches Switch#show interfaces FastEthernet0/1 status Aging Time : 10 mins D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 Generally speaking, the most common services to enable/disable are listed below with their descriptions in Table 9.1: 4.3.cClient Hold-down timers: If a metric for a particular route keeps getting worse, updates for that route are not accepted for a delayed period. Error Disable Recovery R1#show ip route Hold-down timers are used to prevent networks that were previously advertised as down from being placed back into the routing table. When a router receives an update that a network is down, it begins its hold-down timer. This timer tells the router to wait for a specific amount of time before accepting any changes to the status of that network. Today you will learn about the following: Router(config)#ip route 0.0.0.0 0.0.0.0 s0/0 Turn it off with the no auto-summary command: Minimum = 78ms,encor 350 401, Maximum = 188ms, Average = 109ms tcp-keepalives-in Generate keepalives on idle incoming network connections 3.6.dFloating static Switch#show interfaces FastEthernet1/1 switchport Name: Fa0/2 Compiled Wed 18-Jul-07 04:52 by pt_team advertisement version: 2 Distance Vector routing protocols traditionally use a one-dimensional vector when determining the most optimal path(s) through the network, while Link State routing protocols use the Shortest Path First (SPF) when determining the most optimal path(s) through the network. Before delving into the specifics of these two classes of routing protocols, we will first take a look at vectors, as well as at the elusive SPF algorithm.

Free Download Dumps Demo & Study Tools

Latest CCNP Enterprise 350-401 ENCOR Dumps

If you want to pass the first exam successfully, the next you must take a serious look! All of our dumps are verified by IT certified experts. Our Cisco 350-401 ENCOR  CCNP Enterprise Dumps contains all the real topics of the day. What is our goal? To help you pass the exam successfully! You can trust us completely, and we will definitely not let you down. You can find us at anytime because we are willing to serve you guys !

Come on! Do your wisely decision!