cisco 350-501 spcor

cisco 350-501 spcor

Port Vlans allowed on trunk Fa0/6 10, 20 R1(config-router)#network 172.16.0.0 Switch#show interfaces trunk Switch port security 6.Check the mac address table on the switch. 4.3Configure and verify DHCP on a router (excluding static reservations) Sending the packet (switching) ACL Rule 7 – You can reuse the same ACL. S 3FFF:1234:ABCD:2::/64 [1/0] Verify the switch mac address table Configure a password on the VTY lines 6.Configure the same commands on Switch B now. For VLAN creation, put the PC port into VLAN 2, and set the interface to “access” and the trunk link to “trunk.” Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds: Chassis id: 0001.64EE.CB19 Port id: Gig0/1 Day 11 – Static Routing Administrative Mode: dynamic auto Operational Mode: static access Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: native Negotiation of Trunking: On Switch#conf t Switch(config)#int fa0/0 Switch(config-if)#shutdown Switchport: Enabled Administrative Distance 120. The second route is 80.0.0.0/8. This route is learned via internal EIGRP Router#show interface fa0/0 This module maps to the following ICND1 syllabus requirements: Configuring and verifying trunk links Dynamic Trunking Protocol Classless protocols use VLSM (i.e., RIPv2 and EIGRP): R1(config-router)#network 192.168.1.0 Define a couple of VLANs and assign names to them Assign a VLAN to a port configured as switchport access You should always disable the services you are not going to use. Cisco has done a good job by not enabling insecure or rarely used services/protocols by Routing Information Sources: Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: dot1q Negotiation of Trunking: On Switch-1#show port-security address Secure Mac Address Table A trunk is a switch port that can carry multiple traffic types, each tagged with a unique VLAN ID. As data is switched across the trunk port or trunk link, it is tagged (or colored) by the egress switch trunk port, which allows the receiving switch to identify that it belongs to a particular VLAN. On the R1(config-router)#passive-interface f0/1 R1(config-subif)#ip add 10.20.20.1 255.255.255.0 R1(config-subif)#exit 4.4Troubleshoot client- and router-based DHCP connectivity issues 4.6 Configure, verify, and troubleshoot IPv4 standard numbered and named access list for routed interfaces Again, the show interfaces [name] switchport command can be used to 1.Set the router facing interface to trunk. 192.168.1.4/30 VLAN and Trunking Topology Unlike Distance Vector routing protocols, which send their neighbors their entire routing table, Link State routing protocols send incremental updates when a change in the network topology is detected, which makes them more VTP runs in the following three modes: Server (default) Router(config)#access-list 1 permit 192.168.1.4 0.0.0.3 If you wanted to set the router as the NTP server you would add the below command and (optionally) a stratum level. 4.On the right router, turn LLDP off the entire device. You can verify the native VLAN with the commands (issued per interface) illustrated in the output below: You can configure the interface to selectively not send and receive LLDP packets with the no lldp transmit and no lldp receive commands. R2(config-if)#int lo0 TOT/TAT/TNT: 802.1Q/802.1Q/802.1Q DHCP Options R1(config-subif)#ip add 10.30.30.1 255.255.255.0 R1(config-subif)#exit .!!!! The DHCP Pool Configuration mode is also the place where you can configure other DHCP options. In the configuration output above, the following parameters were configured: Take today’s challenges Default routes can be created statically or learned dynamically. In Figure 11.3 above,cisco 350-501 spcor, the static default route is pointing to the edge router. Now, if you didn’t want to keep the entire routing table for the Internet (using BGP) on your edge router and preferred that your Internet Service Provider did this work for you, you typically would receive a dynamic default route via BGP from your ISP as shown below in Figure 11.4. We will cover BGP in the ICND2 section.