ccnp 350 401 dump

ccnp 350 401 dump

• 2819 Reviews

Troubleshooting Trunking and VTP Router(config)#access-list 1 permit 172.20.1.0 0.0.31.255 Based on the contents of this routing table, if the router received a packet destined to 80.1.1.1, it would use the RIP route because this is the most specific entry, even though both EIGRP and OSPF have better administrative distance values and are therefore more preferred route sources. The show ip route 80.1.1.1 command illustrated below can be used to verify this statement: In the previous module, you learned that 802.1Q, or VLAN tagging, inserts a tag into all frames, except those in the native VLAN. The IEEE defined the native VLAN to provide for connectivity to old 802.3 ports that did not understand VLAN tags. Access Mode VLAN: 10 (data) Trunking Native Mode VLAN: 1 (default) Voice VLAN: 11 Some benefits to using VTP include the following: Administrative Mode: dynamic desirable Operational Mode: trunk Last Source Address:Vlan : 0001.C7DD.CB18:1 Instructions Some of the commands that can be used to verify the encapsulation types are as follows: Today you will learn about the following: Configuring static routes Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP R2(config-if)#ipv6 add 2001:aaaa:bbbb:eeee::1/64 R2(config-if)#end Day 7 Tasks %SYS-5-CONFIG_I: Configured from console by console show vlan brief automatically). Additionally, add the IP address 192.168.1.1 to your PC’s FastEthernet interface. Sticky MAC Addresses 0 Setting device VLAN database password tocisco Switch1(config)# 1.Add port security to the switch. Delay Day 14 Labs 2.7.cSticky Router(config)#access-list 1 permit 172.20.1.0 0.0.31.255 Switch-1(config-if-range)#switchport access vlan 20 Switch-1(config-if-range)#switchport mode access Switch-1(config-if-range)#exit Outgoing update filter list for all interfaces is not set This lesson maps to the following CCNA syllabus requirement: address ref clock st when poll reach delay offset disp 2.7Configure, verify, and troubleshoot port security You can use the ip default-network command when IP routing is enabled on the Cisco router. When you configure the ip default-network command, the router considers routes to that network for installation as the gateway of last resort on the router. In the example below,ccnp 350 401 dump, 161.44.191.1 is a next hop router: 9.Change the MAC address on your PC, or if you can’t do this, plug another device into the switch port. This should make the port shut down due to a breach in the security settings. The screenshot below shows where you would change the MAC address in Packet Tracer. Interface: FastEthernet0/1, Port ID (outgoing port): Switch Holdtime: 143 Counting to infinity Split horizon Poison reverse Hold-down timers You can also set an aging time and type on the switch, but this is going beyond the CCNA-level requirements. (Have a try on your own time if you wish.) VLAN Trunking Protocol (VTP) is a Cisco proprietary Layer 2 messaging protocol that manages the addition, deletion, and renaming of VLANs on switches in the same VTP domain. VTP allows VLAN information to propagate through the switched network, which reduces administration Learn how to configure and troubleshoot RIPv2. Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: dot1q Negotiation of Trunking: Off Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#hostname SwitchA traffic Traffic related statistics virtual-links Virtual link information RouterB#ping 172.16.1.1 Type escape sequence to abort. Learn how to configure voice VLANs on a Cisco switch. 3.Ensure the switch interface is up (and an IP address on the PC). S* 198.10.1.0/24 [1/0] via 161.44.191.1 Is the VLAN blocked on the trunk? Enter configuration commands, one per line. End with CNTL/Z. SwitchA(config)#int FastEthernet0/2 Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#line vty 0 ? 2.Create VLAN 2 on the switch. Standard numbered ACLs are the most basic form of ACL you can apply to the router. While they are the easiest to configure, they have the most limited range of filters available. They can only filter based on the source IP address or network. The way to recognize a standard ACL is by the number which precedes the configuration lines; these numbers will be from 1 to 99. System Description:Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.4(3)M3, RELEASE SOFTWARE (fc2)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2015 by Cisco Systems, Inc.Compiled Fri 05- Jun-15 13:24 by prod_rel_team You can also implement this route using the router’s outgoing interface instead of the next hop. So, for example, if Router 1 uses Ethernet 0/2 to connect to Router 2, it would look like this: entry Information for specific neighbor entry interface CDP interface status and configuration neighbors CDP neighbor entries Spend 15 minutes on subnetting.org Review yesterday’s theory notes and labs Switch1(config)#vtp domain passhot 5.4.c. (ii) Telnet/SSH Please ensure that you type out ALL of these commands onto a router. There is no way on Earth that you will remember them by reading them on a page. Try out the configurations, make mistakes, post questions, break it on purpose (not on a live network), and fix it again. Make sure that you memorize the table above for the exam! Type escape sequence to abort. information on the switches, thus reducing the broadcast traffic, as shown in Figure 6.4 below: Cisco has excluded the advanced features of RIP, such as authentication and redistribution, from the syllabus so we won’t go into them here. Switchport: Enabled Administrative Mode: static access Operational Mode: static access Add a Banner Message DHCP servers can be configured to give an IP address to a host for a specified period called the lease time. This can be for hours or days. You can and should reserve IP addresses which cannot be allocated to hosts on the network. These IP addresses will already be in use on router interfaces or for servers. If you fail to do this, you may see duplicate IP address warnings on your network because the DHCP server has allocated your address to a host.

Free Download Dumps Demo & Study Tools

Latest CCNP Enterprise 350-401 ENCOR Dumps

If you want to pass the first exam successfully, the next you must take a serious look! All of our dumps are verified by IT certified experts. Our Cisco 350-401 ENCOR  CCNP Enterprise Dumps contains all the real topics of the day. What is our goal? To help you pass the exam successfully! You can trust us completely, and we will definitely not let you down. You can find us at anytime because we are willing to serve you guys !

Come on! Do your wisely decision!