350-701 study guide

350-701 study guide

• 4502 Reviews

1.Add IP addresses for hosts inside the respective VLANs. DHCP Leases In production networks with Cisco Catalyst 3750 switches, it is always a good idea to determine what the switch will be used for,350-701 study guide, and then select the appropriate Switch Database Management (SDM) template via the sdm prefer {access | default | dual-ipv4-and-ipv6 {default | routing | vlan} | routing Switch(config)#vtp mode server ‹this is on by default Switch(config)#vtp domain passhot Troubleshooting inter-VLAN routing 3.6.cHost route Learn how to configure voice VLANs on a Cisco switch. Usage: Encryption Key Key is not exportable. Key Data: Limit Telnet and SSH access Troubleshooting and verifying ACLs A “network” as it applies to network routing is a remote subnet that you would like to reach. Some examples may be 10.1.0.0/24, 192.168.0.0/16, or 38.122.188.0/25. Basically, if it’s anything below a /31 subnet, then you ultimately would need to rely on a network route to reach it. Building the IP Routing Table If logging is enabled and either the Restrict mode or the Shutdown Violation mode is configured on the switch, messages similar to those shown in the following output will be printed on the switch console, logged into the local buffer, or sent to a syslog server (as per Table 9.2 above): Switch#show cdp nei detail Device ID: IP Phone We have covered a lot of ground so far. Don’t worry about how much is left to learn though. Review the main learning points from switch security, routing concepts, static routing and RIP. Distance: (default is 115) %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan2, changed state to up Switch(config-if)#^Z ‹ press Ctrl+Z keys 6.Add a SVI to VLAN1 and then telnet to the switch using that IP address to test the username and password. 4.Check the LLDP entry again. Normal and detailed. 　　permit host 172.16.2.2 Router# Switch-1#show running-config interface GigabitEthernet0/2 Building configuration... Unlike CDP, LLDP is disabled globally on all supported interfaces, which (of <1-65535> Process ID number The following are examples of problems and possible solutions: Trunk down? The following output illustrates how to enable port security on an interface and to configure a static secure MAC address of 001f:3c59:d63b on a switch access port: Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: dot1q Negotiation of Trunking: On If needed, you can also configure some excluded addresses from the 192.168.1.0/24 range. Let’s say you want to exclude the router interface IP address (192.168.1.1) and the 192.168.1.250 to 192.168.1.255 address range, Cisco routers use the administrative distance, the routing protocol metric, and the prefix length to determine which routes will actually be placed into the routing table, which allows the router to build the routing table. The routing table is built via the following general steps: Static secure MAC addresses Dynamic secure MAC addresses Sticky secure MAC addresses Limit Telnet and SSH access Troubleshooting and verifying ACLs ip default-network 6.Now ping the IP address of L0 on R2. Passive interfaces Routing protocol classes Please take today’s exam at The third trunk port configuration step is to implement configuration to ensure that the port is designated as a trunk port. This can be done in one of two ways: The following example shows the router IP address 172.16.1.1 as the default route: 2.Set the interface on the switch to static access. Router(config)#access-list 1 permit 192.200.1.0 0.0.0.63 Purpose None access list# permit/deny [service/protocol] [source network/IP] [destination network/IP] [port#] Domain name: Network+ When the router receives a packet for a directly connected network, the router checks the routing table and then the packet is forwarded to that network, as shown in Figure 10.1 below: Spend 15 minutes on the subnetting.org website SW1#show interfaces FastEthernet0/1 switchport Name: Fa0/6 Version : The [dot1q] keyword forces the switch port to use IEEE 802.1Q encapsulation. The [isl] keyword forces the switch port to use Cisco ISL encapsulation. The [negotiate] keyword is used to specify that if the Dynamic Inter-Switch Link Protocol (DISL) and the Dynamic Trunking Protocol (DTP) negotiation fails to successfully agree on the encapsulation format, then ISL is the selected format. DISL simplifies the creation of an ISL trunk from two interconnected Fast Ethernet devices. DISL minimizes VLAN trunk configuration procedures because only one end of a link needs to be configured as a trunk.

Free Download Dumps Demo & Study Tools

Latest  350-701 SCOR CCIE Security Dumps

Here are the latest 350-701 SCOR dumps that will help you pass the exam at once.  You don't have to worry about whether the answers to the questions are accurate because each question is reviewed and approved by our professional IT certification experts.  You can trust us because choosing us will never let you down.

Our goal is only one that to help you pass the exam successfully.