350-601 dccor training

350-601 dccor training

------------------------------------------------------------------ 10.You should see your FastEthernet port go down immediately. Capability Codes: R - Router,350-601 dccor training, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone SwitchA(config)#vlan 2 SwitchA(config-vlan)#name passhot Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: dot1q Negotiation of Trunking: On R1(config)#ip route 192.168.2.0 255.255.255.0 172.16.4.2 Ease of use Flexibility ! lines omitted for brevity Gateway of last resort is not set TOT/TAT/TNT: 802.1Q/802.1Q/802.1Q Please take today’s exam at Day 6 Tasks The following configuration outputs correspond to Figure 7.1: Router(config)#ip route 192.168.1.0 255.255.255.0 s0/0 When using DTP on two neighboring switches, if the switch port defaults to a dynamic desirable state, the port will actively attempt to become a trunk. If the switch port defaults to a dynamic auto state, the port will revert to being a trunk only if the neighboring switch is set to dynamic desirable mode. R2#show ntp status Option 129: call server IP address !!!!! Sending 5, 100-byte ICMP Echos to 2001:AAAA:BBBB:CCCC::1, timeout is 2 seconds: line vty 0 15 Now please complete today’s lab at Trying 192.168.1.3 ...Open KEEP OUT OR 6.Now ping the IP address of L0 on R2. Today you will learn about the following: Basic routing Switching Concepts Gig0/1, Gig0/2 One of the major advantages offered by DHCP is the ability to lease an IP address, meaning assigning it on a temporary basis. Usually when a client leaves the network, that particular assigned IP address becomes free and can be allocated to another device by the DHCP server. Sticky MAC Addresses 5 Port Vlans allowed on trunk Fa0/1 1,10,20,30,40,50 Switch(config-if)#switchport trunk encapsulation dot1q Switch(config-if)#switchport mode trunk Switch(config-if)#switchport nonegotiate Switch(config-if)#exit Switch-1#show port-security address Secure Mac Address Table Verifying the Correct Path Selection 7.Set port security on your switch for the FastEthernet port. It will fail if you have not hard set the port to access (as opposed to dynamic or trunk). Switch-1(config-if)#switchport mode access Switch-1(config-if)#switchport port-security ------------------------------------------------------------------ Total entries displayed: 2 SW2#show lldp entry R2 course) means that you must enable LLDP globally to allow a device to send LLDP packets. However, no changes are required at the interface level. The following example shows how to globally enable LLDP: If you use both the ip default-network and the ip route 0.0.0.0 0.0.0.0 commands to configure candidate default networks, the network defined with the ip default-network command will take precedence. ip route 192.168.1.0 255.255.255.0 Ethernet0/2 Router(config)#ip dhcp excluded-address 172.16.1.1 172.16.1.10 Router(config)# Challenge 3 – CDP Lab We already know that the native VLAN is used by the switch to carry specific protocol traffic, such as Cisco Discovery Protocol (CDP), VLAN Trunking Protocol (VTP), Port Aggregation Protocol (PAgP), and Dynamic Trunking Protocol (DTP) information. The default native VLAN is always VLAN 1; however, the native VLAN can be manually changed to any valid VLAN number (except for 0 and 4096, because these are in the reserved range of VLANs).