350-401 practice test

350-401 practice test

• 6661 Reviews

Far more granularity is built into extended numbered ACLs; however, this makes them trickier to configure. You can filter source or destination networks, ports, protocols, and services. RIPv2 Day 8 – Review Router(config)#ip dhcp pool SUBNET_A i - IS-IS, su - IS-IS summary,350-401 practice test, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route To verify that SSH is enabled on the switch, enter the following command: Shutdown VLAN (outside of the CCNA syllabus) S 10.0.0.0 is directly connected, Serial0/1/0 Take off the active interface: Route poisoning: This feature prevents routers from sending packets through a route that has become invalid. Distance Vector protocols use compress-config Compress the configuration file config TFTP load config files SecureStatic address aging : Disabled Security Violation count : 0 The following example shows the router IP address 172.16.1.1 as the default route: ACL Rule 8 – Keep them short! i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Neighbor address 1: 000000000000 Spend some time today repeating the labs from the last few days, do you best to configure them without looking at my walkthrough. Use the question mark rather than look at my answers. You need to start writing out the cram guide from memory also. database RIP database events events RIP protocol events trigger RIP trigger extension neighbors Detailed information on TCP and BGP neighbor connections nsap Address family Switch-1#show port-security address The switchport port-security aging time 10 and switchport port-security aging type inactivity commands were issued under the interface because the aging time default is 0 minutes and the aging type default is absolute. The switchport port-security maximum 10 command was issued under the interface since by default only one MAC address is permitted when port *Mar 1 00:29:15.779: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0/0 assigned DHCP address 10.10.10.2, mask 255.255.255.0, hostname Router Workstations can also manually release the IP address, for example, in these situations: 3.Go into ACL mode and paste in the new ACL. EIGRP uses the interface delay value as part of its metric calculation. Manually adjusting the interface delay value results in the recomputation of the EIGRP metric. Port Vlans in spanning tree forwarding state and not pruned Fa0/6 10, 20 Switch#show interfaces trunk Port Name Status Vlan Duplex Speed Type Fa0/1 errdisabled 100 full 100 100BaseSX Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Sending updates every 30 seconds, next due in 21 seconds Invalid after 180 seconds, holddown 180, flushed after 240 Redistributing: rip This would be applied to the server side router. Remember that there will be an implicit “deny all” at the end of this list, so all other traffic will be blocked. From a connectivity standpoint, some of the things that need to be checked include: Configuring Static Routes Maximum path: 4 DTP settings differ from platform to platform so feel free to alter the settings on your switch so you try out the available commands. Please note the results. The below lab was configured on 2960 model switches using Packet Tracer. Switch CAM tables are storage locations that contain lists of known MAC addresses on physical ports, as well as their VLAN parameters. Dynamically learned contents of the switch CAM table, or MAC address table, can be viewed by issuing the show mac-address-table dynamic command, as illustrated in the following output: Switch(config)#interface FastEthernet0/1 Switch(config-if)#switchport tcp-small-servers Enable small TCP servers (e.g., ECHO) telnet-zeroidle Set TCP window 0 when connection is idle timestamps Timestamp debug/log messages ip route 192.168.1.0 255.255.255.0 Ethernet0/2 In the previous module, you learned that 802.1Q, or VLAN tagging, inserts a tag into all frames, except those in the native VLAN. The IEEE defined the native VLAN to provide for connectivity to old 802.3 ports that did not understand VLAN tags. Counting to infinity Split horizon Poison reverse Hold-down timers Access Control List Rules Verifying the correct path selection DNS Operations Router(config)#int FastEthernet0/0 %LINK-5-CHANGED: Interface Vlan3, changed state to up Switch(config-if)#ip address 192.168.1.1 255.255.255.0 Figure 10.13 depicts the same LAN illustrated in Figure 10.12. In Figure 10.13, however, only a single physical router interface is being used. In order to implement an inter-VLAN routing solution, subinterfaces are configured off the main physical router interface using the interface [name].[subinterface number] global configuration command. Each subinterface is associated with a particular VLAN using the encapsulation [isl|dot1Q] [vlan] subinterface configuration command. The final step is to configure the desired IP address on the interface.

Free Download Dumps Demo & Study Tools

Latest CCNP Enterprise 350-401 ENCOR Dumps

If you want to pass the first exam successfully, the next you must take a serious look! All of our dumps are verified by IT certified experts. Our Cisco 350-401 ENCOR  CCNP Enterprise Dumps contains all the real topics of the day. What is our goal? To help you pass the exam successfully! You can trust us completely, and we will definitely not let you down. You can find us at anytime because we are willing to serve you guys !

Come on! Do your wisely decision!