300 x 410 mm

300 x 410 mm

• 2845 Reviews

Day 10 – Routing Concepts Verify the switch mac address table Configure a password on the VTY lines Services Router(dhcp-config)#dns-server 172.16.1.3 PC>ipconfig /renew 　　　　　　(P) Repeater, (S) Station, (O) Other Device ID Local Intf Hold-time Capability Port Standard numbered ACLs are the easiest to configure, so this is the best place to start. Standard ACLs can only filter based on a source network or IP address. DNS Servers. : 0.0.0.0 FastEthernet0/1 is down, line protocol is down [err-disabled] Default version control: send version 2, receive version 2 Interface Send Recv Triggered RIP Key-chain FastEthernet0/0 2 2 Network Time Protocol Passive Interface(s): The route above is actually a default route. Default routes are used to direct packets addressed to networks not explicitly listed in the routing table. We cover these as well as your other options in more detail below. Routing Metrics 2.Configure a sub-interface on the router, one for each VLAN. Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) Reply from 192.168.1.1: bytes=32 time=188ms TTL=128 Reply from 192.168.1.1: bytes=32 time=78ms TTL=128 Reply from 192.168.1.1: bytes=32 time=94ms TTL=128 Reply from 192.168.1.1: bytes=32 time=79ms TTL=128 Voice VLAN: none 1.Create VLAN 10 for data and VLAN11 for voice traffic on the switch. Today you will learn about the following: ACL basics I’ve already mentioned that you can actually have both a password and an enable secret password on your router and switch, but this can cause confusion. Just set the enable secret password. The configuration file below illustrates how to issue a command without dropping back to Privileged mode by typing do before the command: DTP settings differ from platform to platform so feel free to alter the settings on your switch so you try out the available commands. Please note the results. The below lab was configured on 2960 model switches using Packet Tracer. Total Addresses in System : 5 RouterB#show ip route 172.16.1.1 Routing entry for 172.16.1.0/24 Use the default-information originate command to generate a default route into an OSPF routing domain. switchport port-security mac-address sticky 0004.c16f.8741 switchport port-security mac-address sticky 000c.cea7.f3a0 switchport port-security mac-address sticky 0013.1986.0a20 switchport port-security mac-address sticky 001d.09d4.0238 switchport port-security mac-address sticky 0030.803f.ea81 Learn how routers can be used as DHCP servers. 4.Test Telnet by Telnetting from your PC to your switch. Some important considerations for static default routing: Hold-down timers: If a metric for a particular route keeps getting worse, updates for that route are not accepted for a delayed period. SwitchA(config)#int FastEthernet0/2 SwitchA(config-if)#switchport trunk allowed vlan 2 SwitchA(config-if)#^Z Switch(config-if)#int g0/1 ---- ----------- ---- ----- ------------ Switch-1(config)#interface GigabitEthernet0/2 Switch-1(config-if)#switchport port-security 2.Turn CDP off on the remote interface. Clear the CDP entry on the switch and check the outputs again. The entry should be blank. R1(config-if)#ipv6 add 2001:aaaa:bbbb:cccc::1/64 R1(config-if)#no shut Port numbers S 192.168.4.0/24 is directly connected, Serial0/0/1 Day 10 – Routing Concepts While the other keywords are familiar, because they are also applicable to IPv4 static routes,300 x 410 mm, the [multicast] keyword is exclusive to IPv6 and is used to configure an IPv6 static Multicast route. If this keyword is used, the route will not be entered into the Unicast routing table and will never be used to forward Unicast traffic. To ensure that the route is never installed into the Unicast RIB, Cisco IOS software sets the administrative distance value for the route to 255.

Free Download Dumps Demo & Study Tools

Latest CCNP Enterprise 300-410 ENARSI Dumps 

The best accurate dumps in the world! 300-410 dumps are the most stable and latest in PASSHOT. We have many work experience and help many students passed the exam. The one we can sure that we can help you pass the exam 100 %.