300-435 enauto pdf

300-435 enauto pdf

• 6675 Reviews

Switch#show cdp neighbors Flat and Hierarchical Routing Algorithms %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down Switch# Network convergence occurs when all routers in the network have the same view and agree on optimal routes. When convergence takes a long time to occur, intermittent packet loss and loss of connectivity may be experienced between remote networks. In addition to these problems, slow convergence can result in network routing loops and outright network outages. With static routes, you can specify a next-hop IP address the router needs to go to on the way to the destination address, or you can specify an exit interface. Often, you won’t know your next hop because it is your ISP, or your IP address will change over time (see Figure 11.2 below). If this is the case, use an exit interface. Default Gateway. : 0.0.0.0 Day 13 – Review R1(config)#int lo0 Option 129: call server IP address Spend 15 minutes on subnetting.org Review yesterday’s theory notes and labs Invalid after 0 seconds, hold down 0, flushed after 0 Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Redistributing: isis HTTP secure server trustpoint: VLAN and Trunking (mins) Router(config)#access-list 1 permit 172.20.1.0 0.0.31.255 3.2.aPrefix Topology You won’t be able to test this unless you have internet access on the router. Don’t use live equipment if you have access to routers at work. Routing Metrics Assign an IPv4 address to the directly connected interfaces (10.10.10.1/24 and 10.10.10.2/24) 3.2.bNetwork mask Static Default Routes R1#debug ip rip ? Cisco IOS Software, 1841 Software (C1841-ADVIPSERVICESK9-M), Version 12.4(15)T1, RELEASE SOFTWARE (fc2) You actually wanted the packet to be permitted by the router, but instead it denies it. The reason is the implicit “deny all,” which is a security measure. The matching is done at the binary level, but you can easily configure wildcard masks using the same notation you use for subnet masks. A binary 1 tells the router to ignore the digit and a 0 means match the digit. R1(config-subif)#ip add 10.20.20.1 255.255.255.0 R1(config-subif)#exit This module maps to the following CCNA syllabus requirements: Day 14 Tasks Verify (show) the VTP configuration on both switches is permitted access to a switch port, as well as to limit the number of MAC addresses that can be supported on a single switch port. The methods of port security implementation described in this section are as follows: Switch#show interfaces FastEthernet0/1 status R1(config-if)#ip add 192.168.1.5 255.255.255.252 Media Attachment Unit type: 10 Vlan ID: 1 Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone Entry address(es): Switch(config)#interface FastEthernet1/1 Switch(config-if)#switchport (mins) Switch-1(config-if)#no shutdown Switch-1(config-if)#exit 8.Hard set the MAC address from your PC to be permitted on this port. You can check this with the ipconfig/all command on your PC command line. Then check the port security status and settings. IDSW1 Gi0/2 105 B Gi0/1 Cost R1#show lldp neighbors Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) Reply from 10.20.20.1: bytes=32 time<1ms TTL=127 Reply from 10.20.20.1: bytes=32 time<1ms TTL=127 Reply from 10.20.20.1: bytes=32 time<1ms TTL=127 8.Hard set the MAC address from your PC to be permitted on this port. You can check this with the ipconfig/all command on your PC command line. Then check the port security status and settings. Inter-VLAN Routing 4.Set the hosts ports on the switches to access ports. R2#show ip route Administrative Mode: dynamic desirable Operational Mode: trunk vrf Select a VPN routing/forwarding instance enabled. If an IP address is configured, then this will be included in the CDP message. Router(config-subif)#encap dot1Q 20 192.168.1.1 Day 12 Tasks Path length Reliability overhead in a switched network, whilst enabling switches to exchange and maintain consistent VLAN information. This concept is illustrated in Figure Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#vlan 10 Router(config)#ip host R2 192.168.1.2 Router(config)#ip host R3 192.168.1.3 Router(config)#exit Interface: FastEthernet0/0, Port ID (outgoing port): FastEthernet0/2 Holdtime: 176 VLAN and Trunking RIPv2 Router(config)#ip route 0.0.0.0 0.0.0.0 s0/0 Duplex: full Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: dot1q Negotiation of Trunking: On Day 10 Tasks IA - OSPF inter area, N1 - OSPF NSSA external type 1, DHCP Clients on Cisco Routers Switch-1(config-if)#switchport mode access Switch-1(config-if)#switchport port-security Switch#conf t If you check the routing table, you will see the administrative distance for RIP and the output we covered earlier: Router(config)#ip dhcp pool SUBNET_A Routing protocol algorithms use metrics, which are numerical values that are associated with specific routes. These values are used to prioritize or prefer routes learned by the routing protocol, from the most preferred to the least preferred. In essence,300-435 enauto pdf, the lower the route metric, the more preferred the route by the routing protocol. The route with the lowest metric is typically the route with the least cost or the best route to the destination network. This route will be placed into the routing table and will be used to forward packets to the destination network.

Free Download Dumps Demo & Study Tools

Latest CCNP Enterprise 300-435 ENAUTO Dumps

Are you still looking for stable 300-435 dumps? PASSHOT provide the most stable IT certificated dumps in the world. All of the dumps are verified by IT certified experts.