300-410 exam topics

300-410 exam topics

• 9248 Reviews

With static routes, you can specify a next-hop IP address the router needs to go to on the way to the destination address, or you can specify an exit interface. Often, you won’t know your next hop because it is your ISP, or your IP address will change over time (see Figure 11.2 below). If this is the case, use an exit interface. You will notice that the above two commands are not executed in Router(dhcp-config)# mode. To verify the clients currently served by the router DHCP server,300-410 exam topics, you can use the command below: Please take the day 5 exam at is permitted access to a switch port, as well as to limit the number of MAC addresses that can be supported on a single switch port. The methods of port security implementation described in this section are as follows: This module maps to the following CCNA syllabus requirements: ip route 0.0.0.0 0.0.0.0 (Destination IP) Changing VTP domain name from NULL to passhot Walkthrough * 192.168.1.1 firewall#show crypto key mypubkey rsa Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: dot1q Negotiation of Trunking: On Passive interfaces are usually able to receive routing updates or Hello packets but are not allowed to send any kind of routing protocol information outbound. Challenge 3 – CDP Lab Figure 10.12 illustrates a single switch using two different VLANs, each with an assigned IP subnet. Although the network hosts depicted in the figure are connected to the same physical switch, because they reside in different VLANs, packets between hosts in VLAN 10 and those in VLAN 20 must be routed, while packets within the same VLAN are simply switched. Switch(config)#hostname SwitchOne SwitchOne(config)#ip domain-name mydomain.com SwitchOne(config)#crypto key generate rsa R1#show ipv6 static 3FFF:1234:ABCD:1::/64 detail IPv6 static routes Interface: FastEthernet0/0, Port ID (outgoing port): FastEthernet0/2 Holdtime: 176 1.Create VLAN 10 for data and VLAN11 for voice traffic on the switch. Verifying all the routing protocols that advertise that specific prefix (including static routing) It is a known fact that Distance Vector routing protocols are prone to major problems as a result of their simplistic “routing by rumor” approach. Distance Vector and Link State protocols use different techniques to prevent routing problems. The most important mechanisms include the following (some we have mentioned briefly already): IP address : 192.168.1.2 EIGRP uses the interface delay value as part of its metric calculation. Manually adjusting the interface delay value results in the recomputation of the EIGRP metric. CDP has always been a popular exam topic because it’s both a powerful tool and a potential security risk you need to be aware of. LLDP is a new open standard version and has recently been added to the CCNA syllabus. Router(config)#access-list 1 permit 192.168.1.0 0.0.0.3 {protect | restrict | shutdown | shutdown vlan}] interface configuration command. If a port is shut down due to a security violation, it will show as errdisabled, and the shutdown and then no shutdown command will need to be applied to bring it back up. Domain Name System (DNS) maps host names to IP addresses, enabling you to type “www.passhot.com” into your web browser instead of the IP address of the server on which the site is hosted. 3.Configure your DHCP pool. Then, configure a lease of 3 days, 3 hours, and 5 minutes for your address. Lastly, exclude all the addresses from 1 to 10 from being assigned to hosts. Presume that these are already in use for other servers or interfaces. Switch#show int g0/1 switchport Name: Gig0/1 labels Display labels for IPv4 NLRI specific information HTTP secure server capability: Present HTTP secure server status: Enabled HTTP secure server port: 443 Configuring and Verifying Trunk Links Configured MAC Addresses 1 Switch#show dtp Global DTP information 2.6.bLLDP Device ID Local Intrfce Holdtme Capability Platform Port ID Switch# Port Numbers The full DHCP request and assign process can be seen in Figure 14.2 below: 4.Issue a show ip route and check all networks on both routers Use two directly connected routers and test the basic commands depicted in this module. RIP is covered soon so just copy my commands for now. Router0#show cdp neighbors detail Device ID: Switch0 2passhot active Fa0/1 Port Mode Encapsulation Status Native vlan Fa0/4 on 802.1q trunking 1 Topology 8.Hard set the MAC address from your PC to be permitted on this port. You can check this with the ipconfig/all command on your PC command line. Then check the port security status and settings. ! lines omitted for brevity Gateway of last resort is not set Most routing protocols offer the ability to turn off routing updates per interface. We covered the passive-interface command in detail throughout this guide. The actual behavior of this command will vary from protocol to protocol. For RIP, it will prevent route updates from being multicast from the interface it’s applied to, but incoming updates will be received and processed for use in the routing table.

Free Download Dumps Demo & Study Tools

Latest CCNP Enterprise 300-410 ENARSI Dumps 

The best accurate dumps in the world! 300-410 dumps are the most stable and latest in PASSHOT. We have many work experience and help many students passed the exam. The one we can sure that we can help you pass the exam 100 %.