TS2 Diag3 LAB3

I enter the state is relatively slow, the good thing is that the TS that have been solved successfully and I have more confident. More, exam computer input speed is not slow but the page of the window drag is particularly slow. Anyway, I’m not used to it in the beginning and final part also slow too.

TS2：

Q1, the same solution, e0/0 of sw410

Q2, tra 8.8.8.8 The last one is unreasonable that the solution is a bit anxious and I am not sure about the solution.  I probably sw111 did not announce 201 network segment anyway. It will be passed for a while but the route convergence of the test is very slow, it may make me too anxious.

Q3, R22 lo0 announced to process 10; R10 has route-map, set lp 200, direct no off; sw110 tracert third hop requires no as, sw210 tracert requires as 65001, direct R12, 13 announced direct connection

There is a route-map on Q4 and R20, and you can delete the send community directly.

Q5, R60's crypto's transform-set is wrong and an extra hmac-...

Q6, server1 is not configured with ipv6 address dhcp. This question is very pit when the first direct measurement phenomenon. The first one gives a return package of FE80::666, the second jump is nowhere. I am very strange that do not like this practice and the situation is directly unreachable. And after configuring the server1 to get the ipv6 address, it still doesn't work for a long time and the one side is solved later. After all, the problem is normal.

On Q7 and R3, e0/1 lacks mpls ip, and R3-6 imports its own RT. Because it has no effect, I have not changed it.

Q8, user3 does not have ip add dhcp client e0/0, R30 VLAN2000 2001 gateway is wrong, lease deleted.

Q9, R24 lack ip nhrp map m d, but the phenomenon dmvpn on both 24 and 71 is normal, tangled for a long time and in this case p 10.100.0.1 is actually also open. The demand is user 7 telnet 10.2.200.1

Q10, nat out stat is wrong, the demand is to convert 201.99.70.2 into an address of 123.*.*.*.

Diag3:

Keyword bootp sou 0.0.0.0

Keyword tcp.port==1337 dst port=1337 dst ip=10.1.1.1

CCIE RS LAB3:

Switch mode access is not configured in the provisioning of many switches.

1.1-4: Basically the same, sw2 e2/0-1 is port 2 connected to sw501, e2/2-3 is port 1 connected to sw500, then EC can not be done according to the solution. You must first do trunk and then do EC otherwise EC The sw no is not automatically added to the trunk interface so I checked it for a long time.

2.1: Same as the material given by PASSHOT.

2.2: DC1 OSPF is pre-configured but SW100, 101 LO1 declares ospf, sw110.111 does not pass vlan, bgp also announces 10.1.20x.0/24, check OSPF by the way. Check if there is any Router-ID, etc. .... R30 and R31 establish an IBGP relationship but the provisioning already has

2.3: The process of R100's ospf is 2, the same as the other materials.

2.4-5: Same as the material. Do not knock add ipv4 does not show nei 10.1.13.13 add rece

2.6-7: ebgp has been built, lack of net, lack of summary, lack of bgp agg 0

2.8-9: Same as material is sw110 missing ipv6 unicast

2.10: Requirement agent is loopback1

2.11 R13 show ip pim rp mapping The picture is infor source: 10.1.113.2(?)

Did not make it.

3.1 Basically the same, bgp has no def ipv4, vrf all empty

3.2 crypto R60 51 keyring lack of password, and nhrp lack of password, then R51 shows ikea error. Check the configuration is complete, the rollover interface is useless and finally deleted the keyring to rewrite just fine.

3.3 Same, nat in out is done for you. Write nat in sou list, R60 requires no ip proxy-arp

3.4 Basically the same, R71 uses the nat pool, regardless of it

4.1 Same as the new version

Final part is same too. I’m hungry after the test, I’ll have a meal first and maybe have a time to modify it. Also, I haven’t received a transcript and hope to be smooth!